What's advantages and disadvantages of FRP?

Apr 30, 2020

Leave a message

We often see some bronze sculpture art products in some public places. In fact, many of these sculptures are not real bronze sculpture products, but glass fiber reinforced plastic sculpture products, but they look like bronze sculptures after coloring.


002

FRP is a composite material composed of synthetic resin as the matrix material and glass fiber and its products as the reinforcement materials. FRP sculpture is a finished type of sculpture, which has the characteristics of light weight, corrosion resistance and relatively low cost.

As we all know, steel is very hard and not fragile, but also has the characteristics of high temperature resistance; glass is hard and fragile, with good transparency and high temperature resistance, corrosion resistance and other properties. Smart people began to imagine that if they can produce a glass that has the properties of glass hardness, high temperature resistance, corrosion resistance, and steel as hard and unbreakable, then this material will be of great use.

       Everyone knows that cement blocks are resistant to pressure and steel is resistant to tension. Using steel as the bones and bones and cement as the muscles, let them consolidate into one, complement each other to make up for each other's strength and become extremely strong-this is reinforced concrete.

       In the same way, after countless research experiments, people melted the glass and pulled it into glass fiber as thin as a tenth of the diameter of the hair. The original hard and fragile glass became soft and tensile glass fiber. Its tensile strength can be increased more than ten times. Use fiberglass as the muscles and bones, and use synthetic resin (phenolic plastic, epoxy resin, and polyester resin) as the muscles, and let them congeal into one. The tensile strength of the material is comparable to that of steel-so it is called fiberglass. 


019

So what are the advantages and disadvantages of fiberglass sculpture?

Advantages of fiberglass sculpture

       Lightweight and high-strength density is only 1.5 ~ 2.0, only 1/4 ~ 1/5 of carbon steel, but the tensile strength is close, even more than carbon steel, and the specific strength can be compared with advanced alloy steel.

       Good corrosion resistance Good corrosion resistance, good resistance to the atmosphere, water and general concentrations of acids, alkalis, salts and various oils and solvents.

       Excellent manufacturability, the molding process can be flexibly selected according to the shape, technical requirements, uses and quantity of the product; the process is simple, it can be molded at one time, and the economic effect is outstanding, especially for the products with complex shapes and not easy to form, the number of products is more prominent Process superiority.

       Good designability The materials can be fully selected to meet the performance of the product; various structural products can be flexibly designed according to needs to meet the requirements of use, which can make the product have a good integrity.

Disadvantages of fiberglass sculpture

        1. Aging phenomenon Aging phenomenon is a common defect of plastics, and glass fiber reinforced plastics is no exception. It is easy to cause performance degradation under the action of ultraviolet rays, wind, sand, rain, snow, chemical media, and mechanical stress.

        2. Long-term temperature resistance is poor. Generally, FRP cannot be used for a long time at high temperature. The strength of general polyester glass fiber reinforced plastic at 50 ℃ above is obviously reduced, and generally only used below 100 ℃; the general epoxy glass fiber reinforced plastic at 60 ℃ above, the strength is significantly reduced . However, high temperature resistant resin can be selected to make long-term working temperature at 200 ~ 300 ℃ possible.

        3. Low modulus of elasticity The modulus of elasticity of glass fiber reinforced plastic is two times larger than that of wood, but 10 times smaller than that of steel (E = 2.1 × 106). Therefore, it is often felt that the rigidity of the product structure is insufficient and it is easy to deform. It can be made into a thin shell structure, a sandwich structure, or can be compensated by high modulus fibers or reinforced ribs.

       Nowadays, FRP sculptures are widely used because of their relatively low cost and numerous excellent properties. It often appears in squares, hotels, real estate, parks, homes and other places.

025


Send Inquiry